Trying my new Nox 800-Pinpointing

Only for the discussion of the Minelab Equinox series of metal detector within this forum.
Post Reply
JeffW663
Posts: 7
Joined: Thu Mar 14, 2019 7:06 pm
Has thanked: 30 times
Been thanked: 4 times

Trying my new Nox 800-Pinpointing

Post by JeffW663 »

So here we are with the new detector, having assembled it, charged it up it was time to try it in the garden.
Set it up as suggested on this forum and away we went, well, went as far as inserting, iron screw, ring pull, copper wire and silver cuff-link under the turf, in a clean area, very pleased with the results, all on 'all metal' no problem with locating each type of item with good signals.
Now for the pinpointing, I have read that this machine is not good at this but for me and my machine under these controlled parameters, i.e. knowing where they were, I found the the centre pinpointed was between the cable outlet of the coil and the central boss/joint of the shaft and coil, now if it remains there in the field ? I hope that it may work the same way, or does anyone have thoughts on this please ??



Guppy
Posts: 29
Joined: Thu Apr 11, 2019 6:39 pm
Has thanked: 16 times
Been thanked: 21 times

Re: Trying my new Nox 800-Pinpointing

Post by Guppy »

I've found that pinpointing works well on a coin buried horizontally at about 4", now tip the coin vertically and bury it at 6"+, and pinpointing is not so accurate.

User avatar
Easylife
Posts: 5914
Joined: Mon Apr 24, 2017 9:23 pm
Has thanked: 1659 times
Been thanked: 3191 times

Re: Trying my new Nox 800-Pinpointing

Post by Easylife »

In real life with all detectors the pin-pointing can be thrown out by nearby iron, an odd shaped target, or a target laying at an angle. ::g
Nox 800, 15" coil & Garrett carrot.
White's TDI SL

User avatar
fred
Posts: 11827
Joined: Wed Dec 10, 2014 6:15 pm
Location: Kent
Has thanked: 3241 times
Been thanked: 7430 times

Re: Trying my new Nox 800-Pinpointing

Post by fred »

I am sure that you will be fine with the Nox.

Most signals are fairly straightforward and will pinpoint exactly as you describe. As you get used to the machine you will become able to recognise the deeper signals that may require a little extra care with the pinpointing or the extraction.

Best of luck and do let us know how you get on with it. ::g
Equinox 800 x2

User avatar
Bradrick
Posts: 3125
Joined: Tue Mar 06, 2018 5:07 pm
Location: South Cambs
Has thanked: 2915 times
Been thanked: 1536 times

Re: Trying my new Nox 800-Pinpointing

Post by Bradrick »

JeffW663 wrote:
Tue May 21, 2019 9:34 pm
So here we are with the new detector, having assembled it, charged it up it was time to try it in the garden.
Set it up as suggested on this forum and away we went, well, went as far as inserting, iron screw, ring pull, copper wire and silver cuff-link under the turf, in a clean area, very pleased with the results, all on 'all metal' no problem with locating each type of item with good signals.
Now for the pinpointing, I have read that this machine is not good at this but for me and my machine under these controlled parameters, i.e. knowing where they were, I found the the centre pinpointed was between the cable outlet of the coil and the central boss/joint of the shaft and coil, now if it remains there in the field ? I hope that it may work the same way, or does anyone have thoughts on this please ??
I think that a bit too much is made of the pinpointing abilities of a machine and I wouldn't worry too much about it. The 'wiggle' method usually puts you pretty much over the target for the size of the hole that you are going to dig anyway, and if you have a hand-held pinpointer you will still locate it. Finding the target in the first place is more important, and the nox certainly does that.

Brad
Equinox 800
Garrett 400i
C-Scope 1220b

My life has been full of terrible misfortunes most of which never happened.

Life is difficult. Once we truly know that life is difficult and we truly understand and accept it, then life is no longer difficult.

Ten pence!
Posts: 1360
Joined: Mon Dec 09, 2013 10:42 pm
Location: Norfolk
Has thanked: 503 times
Been thanked: 497 times

Re: Trying my new Nox 800-Pinpointing

Post by Ten pence! »

The target will be in the middle of the coil if the object is shallow, go past say five inches and it could be anywhere! You might get lucky every now and then and the target comes out in the plug but often the sidewall is where it is hiding.

The Equinox clearly has a problem here as countless asks on many forums will confirm, it's very poor compared to the two other machines I also use, my way round it is to dig bigger holes and have the handheld pinpointer at the ready!

Post Reply

Return to “Minelab Equinox Forum”